Single Gem Faceting Machine

Single Faceting Machine new auto how to facet ultratec facetron imahashi sterling gems and lapidary sterlinggemland

This machine is very similar to preforming machine, except that it is performed on one side of a rotating flat disk known as a lap, and it is used especially to create flat surfaces on a stone. Laps are often made of cast iron, steel, or a copper-bronze alloy, but other materials can also be used.

FACETING
How Gem stone cutting faceting factory sri lanka

Faceting is most often done on transparent stones. Flat facets are cut over the entire surface of the stone, usually in a highly symmetrical pattern. The stone is doped (usually with adhesive wax, epoxy, or cyanoacrylate glue) on a metal dopstick, which is then inserted in a faceter that allows precise control of positioning. The cutting angle is adjusted vertically via a protractor and rotationally via an index gear. Faceter rests on a height adjustable table and distance between lap and table is easy adjusted by eccentric movement of the table. The table is easy raised or lowered by micrometer dial to allow the operator accurate control of the cutting depth. The facets are then ground, sanded on a rotating lap, while water or another liquid acts as a coolant and lubricant. When one side (top or bottom) of the stone is finished, a jig is used to transfer the stone to a dopstick on the opposite side.

POLISHING
How Gem Stone Polishing Factory Sri Lanka

After a gemstone is sawed and ground to the desired shape and sanded to remove rough marks left by coarser grits, it is usually polished to a mirror-like finish to aid light reflection from the surface of the stone (or refraction through the stone, in the case of transparent materials). Polishing removes small quantities of stone and can be used, especially when faceting small stones,to do ultra-fine shaping of the stone.

Inspection
How Gem Stone design facet cut inspection europe

Hand Piece does not connected to the machine and may quickly be lifted off the table for inspect the progress of work.

Single Faceting Machine Types

     1. Single Faceting Machine – Two Speed – Normal

Imahashi type single gem cut and polish machine

Description

• 2 Speed Operation – 720 RPM / 1440 RPM.
• Smooth Running Motor – Vibration Free, Low Noise Motor.
• Stainless Steel (Type 304) Shaft/ Parts – Heavy Use, Corrosion Free.
• Cast Aluminum Body – Light Weight, Resist to Corrosion.
• Professional Quality & Durable Design – Water Proof, Vibration Free, Long Lasting, Heat Treated.
• Industrial Grade Powder Coating Layer – Long Lasting Finishing.
• Sealed Special Ball Bearings – Long Lasting, Accurate, Smooth Running.
• Multi-Tasking Design – Faceting, Polishing, and Pre-forming
• User Friendly Design – Comes with one Axle for Use One Lap at a Time, Could Operate by 1 Person.
• Well Made Faceter Table – High Accurate, 3 Axis Movement.
• Vibration Absorb Dimensions and Weight – 65CM Length x 27CM Width x 27CM Height, 27Kg Weight.

      2. Single Faceting Machine – Speed Control – Digital

Single Faceting Machine new auto how to facet ultratec facetron imahashi sterling gems and lapidary sterlinggemland

Description

• Variable Speed Digital Controller 20 RPM to 3000 RPM (Controlled by Knob).
• Build in Keypad – Easy to Start/ Stop, Change Direction.
• High Torque Powerful German Motor – Able to use hardly even at 50 RPM. • Powerful Built in LED Lamp – Flexible Neck, Bright Light.
• Stainless Steel (Type 304) Shaft & Parts – Heavy Use, Corrosion Free.
• Cast Aluminum Body – Light Weight, Resist to Corrosion.
• Professional Quality and Durable Design – Water Proof Axle, Vibration Free, Long Lasting, Heat Treated.
• Industrial Grade Powder Coating Layer – Long Lasting Finishing.
• Sealed Special Ball Bearings – Long Lasting, Accurate, Smooth Running.
• Multi-Tasking Design – Faceting, Polishing, and Pre-forming.
• User Friendly Design – Comes with one Axle for One Lap at a Time, Could Operate by 1 Person.
• Well Made Faceter Table- High Accurate, 3 Axis Movement.
• Vibration Absorb Dimensions and Weight – 61CM Length x 20CM Width x 30CM Height, 27Kg Weight.

      3. Single Faceting Machine – Speed Control – Full Touch

Imahashi Hand piece automatic faceting machine

Note: Optional speed controller (same controller fix on Digital faceting Machine) will supply free of charge for limited time. It will work without touch system and could run the machine even touch system broken.

Description

• Variable Speed Digital Controller – 50 to 3000 RPM (Control by Touch Screen/ Remote/ Rotate Switch).
• Full Touch Screen – Easy to Set speed, Control Speed, direction, and LED lamp.
• Remote Control – Quick remote access to Set speed, Control Speed, direction, and lamp.
• High Torque Powerful Japanese Motor – Able to use hardly even at 50 RPM.
• Powerful Built in LED Lamp – Touch, Flexible Neck, White/ OFF white Bright Light.
• Stainless Steel (Type 304) Shaft & Parts – Heavy Use, Corrosion Free.
• Cast Aluminum Body – Light Weight, Resist to Corrosion.
• Professional Quality and Durable Design – Water Proof Axle, Vibration Free, Long Lasting, Heat Treated.
• Industrial Grade Powder Coating Layer – Long Lasting Finishing.
• Sealed Special Ball Bearings – Long Lasting, Accurate, Smooth Running.
• Multi-Tasking Design – Faceting, Polishing, and Pre-forming.
• User Friendly Design – Comes with one Axle for One Lap at a Time, Could Operate by 1 Person.
• Well Made Faceter Table – High Accurate, 3 Axis Movement.
• Vibration Absorb Dimensions and Weight – 61CM Length x 20CM Width x 30CM Height, 27Kg Weight.

Other accessories may required :

1. Faceter

2. Preforming/ Faceting/ polishing Laps

3. Dopstick – Brass and steel dopstick (Available with 4 shapes and different sizes)

4. Re-charging Roll

5. Adhesive wax, epoxy, or cyanoacrylate glue

6. Transfer jig

7. Polishing agents

Complete Set

Speed Control Hand Peice Faceting Machine
error: checked
%d bloggers like this:
Close Bitnami banner
Bitnami